Showing 30 results for Ceramic
Parisa Rastgoo Oskoui, Mohammad Rezvani, Abbas Kianvash,
Volume 20, Issue 2 (6-2023)
Abstract
Abstract
The effect of different heat-treatment temperatures on the magnetic, crystallization, and structural properties of 20SiO2.50FeO.30CaO (mol%) glass ceramics was studied. The initial glass was synthesized by the sol-gel method at 25℃ with a precursors to solvent ratio of 1/5. After aging the resulted gel for 24 h at room temperature, it was dried in an electric dryer at 110 ℃ . By heat treatment at different temperatures, different phases such as magnetite, maghemite, and hematite were crystallized in the glass. The maximum stability temperature of magnetite and maghemite were 360℃ and 440℃ respectively. By increasing the heat treatment temperature to higher than 440℃ , the oxidation of maghemite to hematite was occureds. The highest magnetization amount (1.9 emu/g) belonged to sample heat treated at 680℃ . By increasing the heat treatment temperature to 840℃ , the magnetization decreased to 0.8 emu/g, due to the oxidation of maghemite. By increasing the heat treatment temperature from 440℃ to 680℃ , crystalline size of maghemite was increased from 40 to 200 nm. By forther increment of temperature to 840℃ , the size of maghemite crystals decreased to 17nm, due to the oxidation of maghemite to hematite.
Abstract
The effect of different heat-treatment temperatures on the magnetic, crystallization, and structural properties of 20SiO2.50FeO.30CaO (mol%) glass ceramics was studied. The initial glass was synthesized by the sol-gel method at 25℃ with a precursors to solvent ratio of 1/5. After aging the resulted gel for 24 h at room temperature, it was dried in an electric dryer at 110 ℃ . By heat treatment at different temperatures, different phases such as magnetite, maghemite, and hematite were crystallized in the glass. The maximum stability temperature of magnetite and maghemite were 360℃ and 440℃ respectively. By increasing the heat treatment temperature to higher than 440℃ , the oxidation of maghemite to hematite was occureds. The highest magnetization amount (1.9 emu/g) belonged to sample heat treated at 680℃ . By increasing the heat treatment temperature to 840℃ , the magnetization decreased to 0.8 emu/g, due to the oxidation of maghemite. By increasing the heat treatment temperature from 440℃ to 680℃ , crystalline size of maghemite was increased from 40 to 200 nm. By forther increment of temperature to 840℃ , the size of maghemite crystals decreased to 17nm, due to the oxidation of maghemite to hematite.
Zahra Shamohammadi Ghahsareh, Sara Banijamali, Alireza Aghaei,
Volume 20, Issue 2 (6-2023)
Abstract
Various analysis techniques were used to investigate the effects of P2O5 on the crystallization, mechanical features, and chemical resistance of canasite-based glass-ceramics. The results showed that canasite-type crystals were the primary crystalline phase in the examined glass-ceramics subjected to the two-step heat treatment, while fluorapatite was the secondary crystalline phase in some specimens. The microstructural observations by field emission electron microscope indicated that the randomly oriented interlocked blade-like canasite crystals decreased with an increase in the P2O5 content of the parent glasses. Among the examined glass-ceramics, the Base-P2 composition (containing 2 weight ratios of P2O5 in the glass) showed the most promising mechanical features (flexural strength of 176 MPa and fracture toughness of 2.9 MPa.m1/2) and chemical resistance (solubility of 2568 µg/cm2). This glass-ceramic could be further considered as a core material for dental restorations.
Ahmed Hafedh Mohammed Mohammed, Khairul Anuar Bin Shariff, Mohamad Hafizi Abu Bakar,
Volume 20, Issue 4 (12-2023)
Abstract
The coated β-tricalcium phosphate (β-TCP) with dicalcium phosphate dihydrate (DCPD) has attracted much attention in the biomaterials field due to the increase in its osteoconductivity. Besides, the porous bioceramic scaffolds with controlled pore sizes are significant in stimulating bone-like cell activity. In this study, the effect of the setting-time process and acidic-calcium phosphate (CaP) concentrations on the fabrication and properties of porous DCPD/ β-TCP scaffolds were studied. Subsequently, the specimens were examined using X-ray diffraction (XRD), scanning electron microscopy (SEM), compression strength and Fourier transforms infrared (FTIR). The study results revealed that the porous DCPD/ β-TCP scaffolds with macro- and micropore sizes were successfully obtained after the 300-600 µm of porous β-TCP granules were exposed to an acidic-CaP solution. Furthermore, the setting-time process and acidic-CaP concentrations increased the DCPD interlocking between granules, and the mechanical strengths of scaffolds increased up to 0.5 MPa. Meanwhile, the porosity levels were changed based on the formation of DCPD crystals. This study was expected to provide novel insights to researchers in the field of bioceramics through its investigation on the creation of porous DCPD/ β-TCP scaffolds.
Sara Ahmadi, Bijan Eftekhari Yekta,
Volume 21, Issue 0 (3-2024)
Abstract
The crystallization behavior and photocatalytic properties of the sol-gel derived glass ceramic coatings in the TiO2-SiO2-B2O3 system were studied. the prepared sol was sprayed on a glazed ceramic wall. Following drying, the coated specimens were fired at 900°C for 1 h. The impact of boron oxide content in the composition was explored in terms of anatase stability and glass maturing temperature. The thermal and crystallization behaviors of the dried gels were studied by the STA, XRD, and FESEM. The photocatalytic property of the coated layer was examined using methylen blue degradation. Based on the results, the sample containing 15 wt% of boron oxide demonestrated about 30% dye removal efficiency, after only 60 min of UV-irradiation. Additionally, this particular sample exhibited the greatest magnitude of the anatase phase in comparison to the other samples.
Ahad Saeidi, Sara Banijamali, Mojgan Heydari,
Volume 21, Issue 2 (6-2024)
Abstract
This study explores the fabrication, structural analysis, and cytocompatibility of cobalt-doped bioactive glass scaffolds for potential applications in bone tissue engineering. A specific glass composition modified from Hench's original formulation was melted, quenched, and ground to an average particle size of 10 μm. The resulting amorphous powder underwent controlled sintering to form green bodies and was extensively characterized using simultaneous differential thermal analysis (DTA), Raman spectroscopy, and Fourier Transform Infrared analysis (FTIR). After mixing with a resin and a dispersant, the composite was used in digital light processing (DLP) 3D printing to construct scaffolds with interconnected macropores. Thermal post-treatment of 3D printed scaffolds, including debinding (Removing the binder that used for shaping) and sintering, was optimized based on thermogravimetric analysis (TG) and the microstructure was examined using FE-SEM and XRD. In vitro bioactivity was assessed by immersion in simulated body fluid (SBF), while cytocompatibility with MC3T3 cells was evaluated through SEM following a series of ethanol dehydrations. The study validates the fabrication of bioactive glass scaffolds with recognized structural and morphological properties, establishing the effects of cobalt doping on glass behavior and its implications for tissue engineering scaffolds. Results show, Low cobalt levels modify the glass network and reduce its Tg to 529 oC, while higher concentrations enhance the structure in point of its connectivity. XRD results shows all prepared glasses are amorphous nature, and DTA suggests a concentration-dependent Tg relationship. Spectroscopy indicates potential Si-O-Co bonding and effects on SiO2 polymerization. Cobalt's nucleating role promotes crystalline phases, enhancing bioactivity seen in rapid CHA layer formation in SBF, advancing the prospects for bone tissue engineering materials.
Mahnaz Dashti, Saeid Baghshahi, Arman Sedghi, Hoda Nourmohammadi,
Volume 21, Issue 3 (9-2024)
Abstract
Abstract
The power line insulators are permanently exposed to various environmental pollutants such as dust and fine particles. This may lead to flashovers and therefore widespread power blackouts and heavy economic damage. One way to overcome this problem is to make the insulator surface superhydrophobic. In this research, the superhydrophobic properties of the insulators were improved by applying room-temperature cured composite coatings consisting of epoxy and hydrophobic nano-silica particles. Either octadecyl trichlorosilane (ODTS) or hexamethyldisilazane (HMDS) was used to coat the silica nanoparticles and make them hydrophobic. Then, the hydrophobic silica was added to a mixture of epoxy resin and hardener. The suspension was applied on the surfaces of a commercial porcelain insulator and cold cured at ambient temperature. The coating increased the water contact angle from 50° to 149°. Even after 244 h exposure to the UV light, the samples preserved their hydrophobic properties. The adhesion of the coating was rated as 4B according to the ASTM D3359 standard. The coating decreased the leakage current by 40% and increased the breakdown voltage by 86% compared to the uncoated sample and showed promise for making power line insulators self-cleaning.
Ahabboud Malika, Gouitaa Najwa, Ahjyaje Fatimazahra, Lamcharfi Taj-Dine, Abdi Farid, Haddad Mustapha,
Volume 21, Issue 4 (12-2024)
Abstract
This paper reports the preparation and characterization of (1-x) PbZr0.52Ti0.48O3 -xBiFeO3 (1-x)PZTxBFO) (x= 0.00, 0.15, 0.30, 0.45, 0.60 and 1.00) multiferroic ceramics which were prepared by a sol-gel method for PZT and hydrothermal reaction process for BFO. The perovskite structure of the composite system was confirmed by X-ray diffraction and Raman spectroscopy, while the composite microstructure w:as char:acterized by scanning electron microscopy. XRD results and Rietveld analysis for the (1-x)PZT-xBFO composites confirm the coexistence of these three phases; rhombohedral (R3m) and tetragonal phases (P4mm) for pure PZT and only the rhombohedral phase (R3c) for pure BFO. Raman spectroscopy of the (1-x)PZT-xBFO composites shows two clear bands around 150 and 180 cm-1. When the BFO content increases, the intensities of Raman modes are decreased. The SEM results suggested a formation of agglomerate and form into large complex clusters as BFO increased and a higher grain size was obtained for the BFO sample compared with the other composites. The EDS spectra of our pellets show that all the characteristic lines of the chemical elements Pb, Zr, Ti, and O and Bi, Fe, and O are present for the PZT and BFO materials respectively. The temperature-dependent dielectric constant shows different behavior dependent on BFO content. Indeed, the dielectric properties are found to be improved with an increase in dopant concentration of BFO in PZT, and novel dielectric behavior, resonance, and antiresonance, were obtained.
Zahra Ghoreishy, Bijan Eftekhari Yekta,
Volume 21, Issue 4 (12-2024)
Abstract
ZrO2 is commonly incorporated into ceramic glass substrates to enhance radiopacity, mechanical strength, and chemical durability. Experience has shown that the crystallization of tetragonal zirconia in glass will have a greater effect on the mechanical properties of ceramic glass. To achieve optimal properties in zirconia, stabilizing oxides are often added to enhance its structural and mechanical qualities. In this research, in order to stabilize the tetragonal phase of zirconia, MgO and CeO2 were added to the glass ceramic composition of the Li2O-SiO2-ZrO2 system and the desired dental substrate was synthesized through the sinter process. The behavior of sintering and crystallization of basic and optimized glass was investigated using HSM and DTA thermal analysis, respectively. The results showed that the optimal sinter temperature, heat press and heat treatment are equal to 730°C, 900°C and 825°C, respectively. Then, in order to determine the crystallization behavior of the prepared samples, X-ray diffraction and microstructure images were used. The results also showed that the presence of the main Li2ZrSi6O15 phase crystallizes at a temperature of 825°C in the base sample and the sample containing ceria. Also, due to early formation of MgSiO3 crystals, magnesia prevents sintering and formation of Li2ZrSi6O15 phase and stability of tetragonal zirconia phase. In the sample containing ceria, during crystallization, ZrO2 entered its crystal structure and led to the stability of the tetragonal zirconia phase at room temperature.
Zainab Dhyaa Fawzy, Saja Ali Muhsin, Taha Hassan Abood,
Volume 22, Issue 2 (6-2025)
Abstract
Ceramics in dentistry have been mainly recommended from a cosmetic perspective. Yet, the hardness behaviour may limit the application in many cases. Although amber glass is used for medications and chemicals, no studies focus on using amber glass for dental purposes as an additive material. This study aims to investigate the dark amber glass behaviour as a new additive material for dental ceramics. The amber glass powder was prepared using the ball mill technique. For the amber glass powder characterization, the SEM/EDX, particle size, DSC, Ion release, and XRD analysis were tested compared to VITA Lumex® AC ceramic. In addition, the Vickers hardness test was applied for ceramic and ceramic amber with an addition of 0.01g, 0.03g, and 0.05g amber glass powder following the DIN EN ISO 6872/ 2019. Statistically, the ANOVA (post hoc- Tukey) test was used for hardness testing analysis at a significant P-value of (P≤0.05). The results show that the amber glass behaviour and composition elements seem similar to VITA ceramics. The addition of amber glass powder to ceramic shows an increase in the HV hardness of specimens. Overall, it was concluded that the amber glass powder could be a promising material for ceramics to use as an additive powder.
Amin Rezaei Chekani, Malek Naderi, Reza Aliasgarian, Yousef Safaei-Naeini,
Volume 22, Issue 2 (6-2025)
Abstract
This paper presents the novel fabrication method of a three-dimensional orthogonally woven (3DW) C/C-SiC-ZrB2 composite and the effects of ZrB2 and SiC particles on microstructure and the ablation behavior of the C/C–SiC–ZrB2 composite are studied. C/C–SiC–ZrB2 composite was prepared by isothermal-chemical vapor infiltration (I-CVI), slurry infiltration (SI), and liquid silicon infiltration (LSI) combined process. Pyrolytic carbon (PyC) was first infused into the 3DW preform by I-CVI at 1050°C using CH4 as a precursor in order to form a C/C preform with porous media. The next step was graphitization at 2400°C for 1hr. Then ZrB2 was introduced into 3DW C/C preform with a void percentage of 48 by impregnating the mixture of ZrB2 and phenolic resin, followed by a pyrolysis step at 1050°C. A liquid Si alloy was infiltrated, at 1650 °C, into the 3DW C/C composites porous media containing the ZrB2 particles to form a SiC–ZrB2 matrix. An oxyacetylene torch flame was utilized to investigate The ablation behavior. ZrB2 particles, along with the SiC matrix situated between carbon fiber bundles, form a compact ZrO2-SiO2 layer. This layer acts as a barrier, restricting oxygen infiltration into the composite and reducing the erosion of carbon fibers. The findings were supported by FESEM imaging and further confirmed through x-ray diffraction and EDS analysis. The addition of ZrB2 to the C/C-SiC composite resulted in a lower mass and linear ablation rate; 2.20 mg/s and 1.4 µm/s respectively while those for C/C-SiC composite were 4.8 mg/s and 6.75 µm/s after ablation under an oxyacetylene flame (2500°C) for 120 s.
